{"product_id":"terraco-terraroc-ns-100","title":"Terraco Terraroc NS 100","description":"\u003cul class=\"tabs\"\u003e\n\u003cli class=\"active\"\u003eDescription\u003c\/li\u003e\n\u003cli\u003eData Sheet\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\u003cli class=\"active\"\u003e\n\u003ch2\u003eTerraco Terraroc NS 100\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eProduct Overview\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Terraroc NS 100 is a general purpose cementitious non-shrink grout designed for narrow void grouting, flow screeds and anchoring of a wide variety of fixings.\u003c\/p\u003e\n\u003cp\u003e- Its non-shrink and free flowing properties are ideally suited for ramming, pumping or pouring.\u003c\/p\u003e\n\u003cp\u003e- The simple addition of a required amount of water determines its wide range of applications.\u003c\/p\u003e\n\u003cp\u003e- Due to its early strength development it allows for quick return to service of grouted areas.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProperties\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Early strength development.\u003c\/p\u003e\n\u003cp\u003e- Non-shrink.\u003c\/p\u003e\n\u003cp\u003e- Can be poured or pumped.\u003c\/p\u003e\n\u003cp\u003e- High compressive strength.\u003c\/p\u003e\n\u003cp\u003e- Chloride free.\u003c\/p\u003e\n\u003cp\u003e- Extensive workability.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAreas Of Use\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Narrowing void grouting (flow-able state).\u003c\/p\u003e\n\u003cp\u003e- Grouting of anchor bolts and manholes.\u003c\/p\u003e\n\u003cp\u003e- Installation of fencing or boundary posts.\u003c\/p\u003e\n\u003cp\u003e- Where grouting of between 10 to 100mm is required (refer to bulking procedure).\u003c\/p\u003e\n\u003cp\u003e- Concrete floor repairs and screeds.\u003c\/p\u003e\n\u003cp\u003e- Machine and pump plinths.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eApplication Method\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePreparation of Surface\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Ensure that all dust, dirt and foreign matter are brushed and scraped away.\u003c\/p\u003e\n\u003cp\u003e- Also ensure the surfaces are free from salts, oil, grease and ridges, and protect all adjacent surfaces not to be covered.\u003c\/p\u003e\n\u003cp\u003e- This must be removed either chemically or mechanically.\u003c\/p\u003e\n\u003cp\u003e- The surface where Terraroc NS 100 is to be applied must be saturated with water for not less than 2 hours prior to application.\u003c\/p\u003e\n\u003cp\u003e- Alternatively Terraco Terrabond A or an epoxy primer (Terraco Epirok EP 1) must be applied to the substrate and the Terraroc NS 100 placed whilst primer is still wet.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMixing Instructions\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Place 3.5 Litres of cold water (25ºC) in the mixing vessel.\u003c\/p\u003e\n\u003cp\u003e- Empty entire contents of 25kg bag Terraroc NS 100 into the water whilst mixing with a mechanical mixer.\u003c\/p\u003e\n\u003cp\u003e- Add additional 500ml water (maximum) to mixture to desired consistency.\u003c\/p\u003e\nMix for 5 minutes and then place or pump.\n\u003cp\u003eSpecification\u003c\/p\u003e\n\u003cp\u003e- Ensure adequate labour is at hand to have continuous mixing and placing of Terraroc NS 100.\u003c\/p\u003e\n\u003cp\u003e- Remove excess water from substrate if saturated with water, if temperature is above 33ºC place grout immediately after mixing.\u003c\/p\u003e\n\u003cp\u003e- When grout is partially set, trim edges and float to desired finish.\u003c\/p\u003e\n\u003cp\u003e- Bulking of Terraroc NS 100 for floor screeds: a) Terraroc NS 100 can be bulked using clean silica sand (0.6 – 1.2mm) at a mixing ratio of 1:1 where screeds of between 20 – 50mm are required. b) For screeds above 50mm, Terraroc NS 100 can be bulked with clean 10mm graded stone at the ratio of 1:1. c) The stone size should never exceed one third of final thickness of floor.\u003c\/p\u003e\n\u003cp\u003e- When bulking with silica aggregate or stone the quantity of water required will be between 9% and 10% (4.5 – 5.0 L per 50 kg mix).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCuring\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Keep surface damp and covered with plastic sheeting or damp hessian cloth.\u003c\/p\u003e\n\u003cp\u003e- The surface can also be kept damp with a fine water spray.\u003c\/p\u003e\n\u003cp\u003e- The curing must be continuous for 3 days.\u003c\/p\u003e\n\u003cp\u003e- Care must be taken where grout is covered by hessian cloth or plastic, ensure that these surfaces are kept damp.\u003c\/p\u003e\n\u003cp\u003e- On exposed vertical surfaces a curing compound can be applied.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0378\/1384\/6151\/files\/Terraco_Terraroc_NS_100.pdf?v=1788330846%20style=\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0378\/1384\/6151\/files\/pdficon.png?v=1593799638\" style=\"width: 50px;\"\u003e\u003cspan style=\"display: table-cell; vertical-align: middle;\"\u003eDownload The Data Sheet Here\u003c\/span\u003e\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Terraco","offers":[{"title":"25Kg","offer_id":45744768942215,"sku":"CC-TER-77260","price":35.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0378\/1384\/6151\/files\/Terraco_Terraroc_NS_100.jpg?v=1788330089","url":"https:\/\/www.bullshardware.com\/products\/terraco-terraroc-ns-100","provider":" Bulls Hardware LLC","version":"1.0","type":"link"}